IC695ALG708 Analog Output Module

There are three models of embedded baseplates, the 311, 313, and 323. These model

numbers are based upon the CPU type that each contains. This chapter discusses only

the baseplate features of these products. CPU specifications for the embedded CPU are

located in Chapter 4. The embedded CPU baseplates have the following features:

The CPU type cannot be changed.

They do not support the use of expansion or remote racks, so these racks do

not have an expansion connector like the modular CPU baseplates do.

The models 311 and 313 are 5-slot baseplates, and the model 323 is a 10-slot

baseplate.

Since they do not require a plug-in CPU module, all numbered slots,

including Slot 1, can be used for I/O or Option modules.

The memory back-up battery is located in the Power Supply module; so if

the Power Supply is unplugged from the baseplate, the battery will be

disconnected from the memory circuits, which are located on the backplane

circuit board. However, the backplane circuit board contains a high value

capacitor, sometimes called a ”super capacitor,” that can store enough charge

to maintain the memory circuits for about 1 hour if the Power Supply is

removed or its battery is disconnected. Chapter 6 discusses the

IC693ACC315 Battery Accessory kit that can be used to maintain memory

contents when the Power Supply is removed from an embedded CPU

baseplate.

There are no configuration switches or jumpers on the Model 311, 313, or

323 baseplates.

An embedded CPU baseplate is always assigned, by default, Rack Number

Zero (0).

A Power Supply module must be plugged into the left slot (which is not

numbered) of these baseplates. The left slot is a unique size and type that

only supports a Power Supply module.

A CPU module (or a special Option module) must be installed in Slot 1 of

these baseplates. Slot 1 is a unique size and type that only supports a CPU

module or a special Option module like the FIP Remote I/O Scanner

(IC693BEM330). Slot 1 is labeled CPU/1.

Slots numbered 2 and above are of a unique size and type that only

supports I/O or Option modules.

Expansion and Remote baseplates are supported, so a 25-pin D-type female

expansion connector is located at the right end of the baseplate for

connecting to an Expansion or Remote baseplate.

Since the CPU is modular, it can be replaced or changed to a different type if

additional features are desired.

Only one CPU baseplate is allowed per system. If more than one baseplate

is used in a system, the additional ones must be either Expansion or Remote

types.

A modular CPU baseplate is always assigned, by default, Rack Number 0.

The Series 90-30 I/O modules described in this manual can be controlled two ways:

1. With a Series 90-30 Programmable Logic Controller (PLC).

2. With a Personal Computer (PC) that has an installed Personal Computer Interface card (or

similar interface). This allows software on the PC to control and monitor Series 90-30 I/O.

If you are using Series 90-30 I/O as part of a Series 90-30 PLC system, you should refer to

GFK-0356, the Series 90-30 Programmable Controller Installation manual, for more information.

If you are using a Personal Computer to control the Series 90-30 I/O, refer to the documentation

for the PCIF, your Personal Computer, and your application software for more information.

In addition to Series 90-30 I/O modules, the I/O system supports a wide variety of option

modules, such as

Genius Communications and Bus Controller

Communications Control module (for serial communications)

Programmable Coprocessor Modules and Alphanumeric Display Coprocessor

Motion control and High Speed Counter modules

Ethernet interface,

Various bus controllers.

State Logic modules

-----------------------------

IC695ALG626RS Refurbished Analog Input HART module, 16 channels single ended, 8 channels differential,channels are configurable for voltage,current and current/ HART. Supports Current: 0 to 20mA, 4 to 20mA, +/- 20mA; Voltage: +/- 10V, 0 to 10V, +/- 5V, 0 to 5V, 1

IC695ALG628 Analog Input HART module, 8 channels single ended, 4 channels differential,channels are configurable for voltage,current and current/ HART. Supports Current: 0 to 20mA, 4 to 20mA, +/- 20mA;  Voltage: +/- 10V, 0 to 10V, +/- 5V, 0 to 5V, 1 to 5V.  The

IC695ALG628RS Refurbished Analog Input HART module, 8 channels single ended, 4 channels differential,channels are configurable for voltage,current and current/ HART. Supports Current: 0 to 20mA, 4 to 20mA, +/- 20mA; Voltage: +/- 10V, 0 to 10V, +/- 5V, 0 to 5V, 1 t

IC695ALG704 Analog Output Module, 4 channels,that is configurable for voltage and current, configured for Current: 0 to 20mA, 4 to 20mA;  Voltage: +/- 10 VDC, 0 to 10VDC per channel non isolated.  Up to 16 bit resolution. Requires high capacity terminal block IC

IC695ALG704CA Conformal Coated Analog Output Module,4 channel voltage/current.  Module  does not include terminal block.

IC695ALG708 Analog Output Module, 8 channels,that is configurable for voltage and current, configured for Current: 0 to 20mA, 4 to 20mA;  Voltage: +/- 10 VDC, 0 to 10VDC per channel non isolated.  Up to 16 bit resolution. Requires high capacity terminal block IC

IC695ALG708CA Conformal Coated Analog Output Module,8 channel voltage/current.  Moduledoes not include terminal block.

IC695ALG708LT Low Temperature Tested (-40 to 60C) Analog Output Module, 8 channels,that is configurable for voltage and current, configured for Current: 0 to 20mA, 4 to 20mA;  Voltage: +/- 10 VDC, 0 to 10VDC per channel non isolated.  Up to 16 bit resolution. Requ

IC695ALG728 Analog Output HART Module, 8 channels,that is configurable for voltage, current, current/HART configured for Current: 0 to 20mA, 4 to 20mA; Voltage: +/- 10VDC, 0 to 10VDC per channel non isolated.  Up to 16 bit resolution.  Requires high capacity ter

IC695ALG808 Isolated Analog Output module, 8 channels, that is configurable for voltage and current.  Requires high capacity terminal block IC694TBB032 or IC694TBS032.

IC695ALG808CA RX3i Isolated Analog Output module conformal coated, 8 channels, that is configurable for voltage and current.  Requires high capacity terminal block IC694TBB032 or IC694TBS032.

IC695CBL001 Energy Pack Cable, 3 ft. (0.91m)

IC695CDEM002 RX3i type 2 demo case for Chinese market.  Demo includes CPU, power supply, Ethernet, input simulator, output with ESCP, high speed counter, Universal analog and analog output modules.  Demo also includes QuickPanel control/view includes thermocouple

IC695CEP001 RX3i CEP CARRIER W/ RJ45 COPPER ETHERNET

IC695CHS007 7 Slot Universal Base.  Slot 0 limited to power supply (IC695PSxxx) only and slot 6 is a PCI slot only (IC695xxx).  Slots 1 through 5 support both PCI and high speed serial connection (IC695xxx and IC694xxx)

IC695CHS007CA RX3i 7-slot Universal Backplane Conf Coa

IC695CHS007LT RX3i 7-slot Universal Backplane Low Temperature tested.

IC695CHS012 RX3i 12 slot universal base

IC695CHS012CA RX3i 12 slot universal backplane. Conformal Coated.

IC695CHS012LT Low Temperature Tested (-40 to 60C) RX3i 12 slot universal base

IC695CHS016 RX3i 16 universal modules slots base

IC695CHS016CA RX3i 16 universal slots backplane with conformal coating.

IC695CHS016LT Low Temperature Tested (-40 to 60C) RX3i 16 universal modules slots base

IC695CMM002 RX3i serial communications module.  Two isolated RS-232/485 port.  Supports Serial Read/Write and Modbus Master/Slave.  Requires Unversal Backplane.

IC695CMM002CA RX3i serial communications module.  Two isolated RS-232/485 port.  Supports Serial Read/Write and Modbus Master/Slave.  Requires Unversal Backplane. Conformal Coated

IC695CMM002LT Low Temperature Tested (-40 to 60C) RX3i serial communications module. Two isolated RS-232/485 port.  Supports Serial Read/Write and Modbus Master/Slave.  Requires Unversal Backplane.

IC695CMM004 RX3i serial communications module.  Four isolated RS-232/485 port.  Supports Serial Read/Write and Modbus Master/Slave.  Requires Unversal Backplane.

IC695CMM004LT Low Temperature Tested (-40 to 60C) RX3i serial communications module. Four isolated RS-232/485 port.  Supports Serial Read/Write and Modbus Master/Slave.  Requires Unversal Backplane.

IC695CMU310RS Refurbished The CMU310 is on marketing hold due to component shortage. Please quote