IC695ALG608 Analog Input module
IC695ALG608 Analog Input module
There are three models of embedded baseplates, the 311, 313, and 323. These model
numbers are based upon the CPU type that each contains. This chapter discusses only
the baseplate features of these products. CPU specifications for the embedded CPU are
located in Chapter 4. The embedded CPU baseplates have the following features:
The CPU type cannot be changed.
They do not support the use of expansion or remote racks, so these racks do
not have an expansion connector like the modular CPU baseplates do.
The models 311 and 313 are 5-slot baseplates, and the model 323 is a 10-slot
baseplate.
Since they do not require a plug-in CPU module, all numbered slots,
including Slot 1, can be used for I/O or Option modules.
The memory back-up battery is located in the Power Supply module; so if
the Power Supply is unplugged from the baseplate, the battery will be
disconnected from the memory circuits, which are located on the backplane
circuit board. However, the backplane circuit board contains a high value
capacitor, sometimes called a ”super capacitor,” that can store enough charge
to maintain the memory circuits for about 1 hour if the Power Supply is
removed or its battery is disconnected. Chapter 6 discusses the
IC693ACC315 Battery Accessory kit that can be used to maintain memory
contents when the Power Supply is removed from an embedded CPU
baseplate.
There are no configuration switches or jumpers on the Model 311, 313, or
323 baseplates.
An embedded CPU baseplate is always assigned, by default, Rack Number
Zero (0).
A Power Supply module must be plugged into the left slot (which is not
numbered) of these baseplates. The left slot is a unique size and type that
only supports a Power Supply module.
A CPU module (or a special Option module) must be installed in Slot 1 of
these baseplates. Slot 1 is a unique size and type that only supports a CPU
module or a special Option module like the FIP Remote I/O Scanner
(IC693BEM330). Slot 1 is labeled CPU/1.
Slots numbered 2 and above are of a unique size and type that only
supports I/O or Option modules.
Expansion and Remote baseplates are supported, so a 25-pin D-type female
expansion connector is located at the right end of the baseplate for
connecting to an Expansion or Remote baseplate.
Since the CPU is modular, it can be replaced or changed to a different type if
additional features are desired.
Only one CPU baseplate is allowed per system. If more than one baseplate
is used in a system, the additional ones must be either Expansion or Remote
types.
A modular CPU baseplate is always assigned, by default, Rack Number 0.
The Series 90-30 I/O modules described in this manual can be controlled two ways:
1. With a Series 90-30 Programmable Logic Controller (PLC).
2. With a Personal Computer (PC) that has an installed Personal Computer Interface card (or
similar interface). This allows software on the PC to control and monitor Series 90-30 I/O.
If you are using Series 90-30 I/O as part of a Series 90-30 PLC system, you should refer to
GFK-0356, the Series 90-30 Programmable Controller Installation manual, for more information.
If you are using a Personal Computer to control the Series 90-30 I/O, refer to the documentation
for the PCIF, your Personal Computer, and your application software for more information.
In addition to Series 90-30 I/O modules, the I/O system supports a wide variety of option
modules, such as
Genius Communications and Bus Controller
Communications Control module (for serial communications)
Programmable Coprocessor Modules and Alphanumeric Display Coprocessor
Motion control and High Speed Counter modules
Ethernet interface,
Various bus controllers.
State Logic modules
-----------------------------
IC694MDL732 Output module 12/24 VDC 0.5 amps 8 points, positive logic.
IC694MDL734 Output module 125VDC 1 amp 6 points isolated POS/NEG logic.
IC694MDL734CA Conformal Coated Output module 125VDC, 1amp, 6 point, isolated per point.
IC694MDL740 Output module 12/24 VDC 0.5 amps 16 points, positive logic.
IC694MDL740CA Conformal Coated Output module 12/24 VDC 0.5 amps 16 points, positive logic.
IC694MDL741 Output module 12/24 VDC 0.5 amps 16 points, negative logic.
IC694MDL741CA Conformal Coated Output module 12/24 VDC 0.5 amp 16 points NEG logic.
IC694MDL741LT Low Temperature Tested Output module 12/24 VDC 0.5 amps 16 points, negative logic.
IC694MDL742 Output module 12/24VDC, 1 amp 16 point positive logic ESCP protection.
IC694MDL742LT Low Temperature Tested Output module 12/24VDC, 1 amp 16 point positive logic ESCP protection.
IC694MDL752 Output module 5/24VDC (TTL) 0.5 amp 32 point negative logic.
IC694MDL752CA Conformal Coated Output module, 5/12-24VDC, 32 point NEG logic.
IC694MDL752LT Low Temperature Tested Output module 5/24VDC (TTL) 0.5 amp 32 point negative logic.
IC694MDL753 Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.
IC694MDL753CA Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.
IC694MDL753LT Low Temperature Tested Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.
IC694MDL754 12/24VDC Output (0.75 amps/point)Module 32 point. Requires terminal block IC694TBBx32 box style or IC694TBSx32 spring clamp. Terminal block is sold seperately. Output response Time is 0.5ms.
IC694MDL754CA Conformal Coated. 12/24VDC Output (0.75 amps/point)Module 32 point. Requires terminal block IC694TBBx32 box style or IC694TBSx32 spring clamp. Terminal block is sold seperately. Output response Time is 0.5ms.
IC694MDL758 Output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032. Terminal block doesn't ship with module.
IC694MDL758CA Conformal Coated version output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032. Terminal block doesn't ship with module.
IC694MDL758LT Low Temperature version output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032. Terminal block doesn't ship with module.
IC694MDL916 Output module, Isolated Relay, Normally Open, 4 Amp, 16 point. Requires High Density Terminal Block (IC694TBBx32 or IC694TBSx32). Only compatible with RX3i.Compatible high speed serial bus on both Universal Base and Standard expansion base.
IC694MDL930 Output module, relay 4 amp, 8 point isolated per point.
IC694MDL930CA Conformal Coated Relay Output module, 4 amp 8 point isolated
IC694MDL931 Output module, relay 3 amp form B and C; 8 point isolated
IC694MDL940 Output module, relay 2 amp 16 point, non isolated.
IC694MDL940CA Conformal Coated Relay Output module 2 amp, non isolated 16 points.
IC694MDL940LT Low Temperature Tested Output module, relay 2 amp 16 point, non isolated.
IC694MDR390 Mixed I/O, 24Vdc Input (8 points), Relay Output (8 points)
IC694PSK001 Kit consists of: (1) IC694PSM001 module, (1) IC694ACC200 terminal assembly and (2) IC694CBL200 interface cables.
IC694PWR321 Power Supply 120/240 VAC 125 VDC Standard
IC694PWR321CA Conformal Coated Power Supply 120/240VAC, standard.
IC694PWR330 Power Supply 120/240 Vac 125 Vdc High Capacity
IC694PWR330CA Conformal Coated Power Supply 120/240VAC 125VDC, added capacity.
IC694PWR331 Power Supply 24 Vdc High Capacity.
IC694PWR331CA Conformal Coated Power Supply 24VDC, added capacity
IC694RTB032 High Density remote block, 32 point, terminal block. Compatible with IC695ALGxxx, IC694MDL660 and IC693MDL660 modules only. Output modules not supported. Requires a IC694TBC032 and a IC694CBL005, IC694CBL010, IC694CBL030, IC694CBL130 cable.
IC694TBB032 Box Style High Density Terminal Block - 36 Connections
IC694TBB132 Box Style High Density Terminal Block with extended depth for large wires - 36 Connections
IC694TBC032 High Density, 32 point, terminal block with cable connector. Compatible with IC695ALGxxx, IC694MDL660 and IC693MDL660 modules only. Output modules not supported. Requires a IC694CBL005, IC694CBL010, IC694CBL030 IC694CBL130 cable. Compatible with
IC694TBS032 Spring Clamp Style High Density Terminal Block - 36 Connections
IC694TBS132 Spring clamp style High Density Terminal Block with extended depth for l arge wires - 36 Connections
IC695ACC002 Replacement plastic cases for RX3i CPU and AC PS, quantity 4. Does not include front cover.
IC695ACC003 Door labels for RX3i IC695xxx I/O modules. Kit includes 2 each of IC695ALG600, IC695ALG608, IC695ALG616, IC695ALG626, IC695ALG628, IC695ALG704, IC695ALG708, IC695ALG728, IC695HSC304, IC695HSC308
IC695ACC302 Auxiliary Smart Battery Module for PACSystems. Provides low battery signal to the CPU. Module mounts external to the controller.
IC695ACC400 RX3i CPU Energy Pack. Compatible with IC695CPE305 and IC695CPE310 only. Energy Pack ships with CPE305 and CPE310.
IC695ACC400CA Conformal Coated. RX3i CPU Energy Pack. Compatible with IC695CPE305 and IC695CPE310 only. Energy Pack ships with CPE305 and CPE310.
IC695ACC402 ENERGY PACK FOR RX3i CONTROLLER
IC695ACC600 RX3i Cold Junction Compensation Kit for Universal Analog Input IC695ALG600
IC695ACC650 Series 90-70 to RX3i Mechanical Frame
IC695ACC651 SERIES 90-70 TO RX3I I/O ADAPTER CARD
IC695ACC652 Series 90-70 to RX3i 5-Slot Conv Rack
Delivery:
Warranty:
All our products are covered by our own warranty.
Payment method:
Quick Quote: Receive price and availability today!
Replacing an electrical equipment unit in a plant is a complex task that requires careful planning and execution to ensure safety and minimize downtime. Here is a general step-by-step guide on how to replace electrical equipment in a plant:
Pre-Planning:
Safety Precautions:
Shutdown Procedures:
Disconnection:
Removal of Existing Equipment:
Installation of New Equipment:
Testing and Commissioning:
Documentation:
Training:
Startup:
Throughout the process, it’s important to work closely with a team that includes electrical engineers, technicians, and maintenance staff. Communication is key to a successful equipment replacement. Additionally, always adhere to local electrical codes and standards to ensure compliance and safety. If the task is beyond the expertise of in-house staff, consider hiring a professional contractor experienced in industrial electrical work.
Obtaining industrial automation programming software typically involves the following steps:
Identify Your Needs:
Research Software Options:
Contact Equipment Manufacturers:
Purchase or Download:
Academic or Evaluation Versions:
Open Source Options:
Licensing:
Training and Support:
Legal and Compliance:
Installation and Setup:
Here are some common ways to obtain industrial automation programming software:
Remember to keep your software updated to benefit from the latest features and security patches. Also, ensure that you have the necessary backup and recovery procedures in place to protect your programming work.
Region Email:
All new products and surplus products of the industrial intelligence industry, as well as the discontinued products of the original manufacturers. We are not an authorized distributor or representative of any of the above manufacturers (except for brand authorization). The trademarks, brand names and brands appearing in this agreement are the property of their respective manufacturers.
COPYRIGHT© 2003-2024 Copyrighted
Phone(WeChat)
+086-18144100983
No 1134 Jimei North Road, Jimei District
Hong Kong Office:
Guan Tang District, Hong Kong,