IC695ALG312 Isolated Thermocouple Input module

There are three models of embedded baseplates, the 311, 313, and 323. These model

numbers are based upon the CPU type that each contains. This chapter discusses only

the baseplate features of these products. CPU specifications for the embedded CPU are

located in Chapter 4. The embedded CPU baseplates have the following features:

The CPU type cannot be changed.

They do not support the use of expansion or remote racks, so these racks do

not have an expansion connector like the modular CPU baseplates do.

The models 311 and 313 are 5-slot baseplates, and the model 323 is a 10-slot

baseplate.

Since they do not require a plug-in CPU module, all numbered slots,

including Slot 1, can be used for I/O or Option modules.

The memory back-up battery is located in the Power Supply module; so if

the Power Supply is unplugged from the baseplate, the battery will be

disconnected from the memory circuits, which are located on the backplane

circuit board. However, the backplane circuit board contains a high value

capacitor, sometimes called a ”super capacitor,” that can store enough charge

to maintain the memory circuits for about 1 hour if the Power Supply is

removed or its battery is disconnected. Chapter 6 discusses the

IC693ACC315 Battery Accessory kit that can be used to maintain memory

contents when the Power Supply is removed from an embedded CPU

baseplate.

There are no configuration switches or jumpers on the Model 311, 313, or

323 baseplates.

An embedded CPU baseplate is always assigned, by default, Rack Number

Zero (0).

A Power Supply module must be plugged into the left slot (which is not

numbered) of these baseplates. The left slot is a unique size and type that

only supports a Power Supply module.

A CPU module (or a special Option module) must be installed in Slot 1 of

these baseplates. Slot 1 is a unique size and type that only supports a CPU

module or a special Option module like the FIP Remote I/O Scanner

(IC693BEM330). Slot 1 is labeled CPU/1.

Slots numbered 2 and above are of a unique size and type that only

supports I/O or Option modules.

Expansion and Remote baseplates are supported, so a 25-pin D-type female

expansion connector is located at the right end of the baseplate for

connecting to an Expansion or Remote baseplate.

Since the CPU is modular, it can be replaced or changed to a different type if

additional features are desired.

Only one CPU baseplate is allowed per system. If more than one baseplate

is used in a system, the additional ones must be either Expansion or Remote

types.

A modular CPU baseplate is always assigned, by default, Rack Number 0.

The Series 90-30 I/O modules described in this manual can be controlled two ways:

1. With a Series 90-30 Programmable Logic Controller (PLC).

2. With a Personal Computer (PC) that has an installed Personal Computer Interface card (or

similar interface). This allows software on the PC to control and monitor Series 90-30 I/O.

If you are using Series 90-30 I/O as part of a Series 90-30 PLC system, you should refer to

GFK-0356, the Series 90-30 Programmable Controller Installation manual, for more information.

If you are using a Personal Computer to control the Series 90-30 I/O, refer to the documentation

for the PCIF, your Personal Computer, and your application software for more information.

In addition to Series 90-30 I/O modules, the I/O system supports a wide variety of option

modules, such as

Genius Communications and Bus Controller

Communications Control module (for serial communications)

Programmable Coprocessor Modules and Alphanumeric Display Coprocessor

Motion control and High Speed Counter modules

Ethernet interface,

Various bus controllers.

State Logic modules

-----------------------------

IC694MDL732 Output module 12/24 VDC 0.5 amps 8 points, positive logic.

IC694MDL734 Output module 125VDC 1 amp 6 points isolated POS/NEG logic.

IC694MDL734CA Conformal Coated Output module 125VDC, 1amp, 6 point, isolated per point.

IC694MDL740 Output module 12/24 VDC 0.5 amps 16 points, positive logic.

IC694MDL740CA Conformal Coated Output module 12/24 VDC 0.5 amps 16 points, positive logic.

IC694MDL741 Output module 12/24 VDC 0.5 amps 16 points, negative logic.

IC694MDL741CA Conformal Coated Output module 12/24 VDC 0.5 amp 16 points NEG logic.

IC694MDL741LT Low Temperature Tested Output module 12/24 VDC 0.5 amps 16 points, negative logic.

IC694MDL742 Output module 12/24VDC, 1 amp 16 point positive logic ESCP protection.

IC694MDL742LT Low Temperature Tested Output module 12/24VDC, 1 amp 16 point positive logic ESCP protection.

IC694MDL752 Output module 5/24VDC (TTL) 0.5 amp 32 point negative logic.

IC694MDL752CA Conformal Coated Output module, 5/12-24VDC, 32 point NEG logic.

IC694MDL752LT Low Temperature Tested Output module 5/24VDC (TTL) 0.5 amp 32 point negative logic.

IC694MDL753 Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.

IC694MDL753CA Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.

IC694MDL753LT Low Temperature Tested Output module, 12/24VDC POS logic, 32 points. Interface uses Fujitsu connector.

IC694MDL754 12/24VDC Output (0.75 amps/point)Module 32 point. Requires terminal block IC694TBBx32 box style or IC694TBSx32 spring clamp.  Terminal block is sold seperately. Output response Time is 0.5ms.

IC694MDL754CA Conformal Coated.  12/24VDC Output (0.75 amps/point)Module 32 point. Requires terminal block IC694TBBx32 box style or IC694TBSx32 spring clamp.  Terminal block is sold seperately. Output response Time is 0.5ms.

IC694MDL758 Output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032.  Terminal block doesn't ship with module.

IC694MDL758CA Conformal Coated version output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032.  Terminal block doesn't ship with module.

IC694MDL758LT Low Temperature version output module, 12/24VDC POS logic, 32 points, 0.5amp per point. Module requires terminal block IC694TBx032.  Terminal block doesn't ship with module.

IC694MDL916 Output module, Isolated Relay, Normally Open, 4 Amp, 16 point.  Requires High Density Terminal Block (IC694TBBx32 or IC694TBSx32).  Only compatible with RX3i.Compatible high speed serial bus on both Universal Base and Standard expansion base.

IC694MDL930 Output module, relay 4 amp, 8 point isolated per point.

IC694MDL930CA Conformal Coated Relay Output module, 4 amp 8 point isolated

IC694MDL931 Output module, relay 3 amp form B and C; 8 point isolated

IC694MDL940 Output module, relay 2 amp 16 point, non isolated.

IC694MDL940CA Conformal Coated Relay Output module 2 amp, non isolated 16 points.

IC694MDL940LT Low Temperature Tested Output module, relay 2 amp 16 point, non isolated.

IC694MDR390 Mixed I/O, 24Vdc Input (8 points), Relay Output (8 points)

IC694PSK001 Kit consists of:  (1) IC694PSM001 module, (1) IC694ACC200 terminal assembly and (2) IC694CBL200 interface cables.

IC694PWR321 Power Supply 120/240 VAC 125 VDC Standard

IC694PWR321CA Conformal Coated Power Supply 120/240VAC, standard.

IC694PWR330 Power Supply 120/240 Vac 125 Vdc High Capacity

IC694PWR330CA Conformal Coated Power Supply 120/240VAC 125VDC, added capacity.

IC694PWR331 Power Supply 24 Vdc High Capacity.

IC694PWR331CA Conformal Coated Power Supply 24VDC, added capacity

IC694RTB032 High Density remote block, 32 point, terminal block.  Compatible with IC695ALGxxx, IC694MDL660 and IC693MDL660 modules only.  Output modules not supported.  Requires a IC694TBC032 and a IC694CBL005, IC694CBL010, IC694CBL030, IC694CBL130 cable.

IC694TBB032 Box Style High Density Terminal Block - 36 Connections

IC694TBB132 Box Style High Density Terminal Block with extended depth for large wires - 36 Connections

IC694TBC032 High Density, 32 point, terminal block with cable connector.  Compatible with IC695ALGxxx, IC694MDL660 and IC693MDL660 modules only.  Output modules not supported.  Requires a IC694CBL005, IC694CBL010, IC694CBL030 IC694CBL130 cable.  Compatible with

IC694TBS032 Spring Clamp Style High Density Terminal Block - 36 Connections

IC694TBS132 Spring clamp style High Density Terminal Block with extended depth for l arge wires - 36 Connections

IC695ACC002 Replacement plastic cases for RX3i CPU and AC PS, quantity 4.  Does not include front cover.

IC695ACC003 Door labels for RX3i IC695xxx I/O modules. Kit includes 2 each of IC695ALG600, IC695ALG608, IC695ALG616, IC695ALG626, IC695ALG628, IC695ALG704, IC695ALG708, IC695ALG728, IC695HSC304, IC695HSC308

IC695ACC302 Auxiliary Smart Battery Module for PACSystems.  Provides low battery signal to the CPU.  Module mounts external to the controller.

IC695ACC400 RX3i CPU Energy Pack.  Compatible with IC695CPE305 and IC695CPE310 only. Energy Pack ships with CPE305 and CPE310.

IC695ACC400CA Conformal Coated.  RX3i CPU Energy Pack.  Compatible with IC695CPE305 and IC695CPE310 only. Energy Pack ships with CPE305 and CPE310.

IC695ACC402 ENERGY PACK FOR RX3i CONTROLLER

IC695ACC600 RX3i Cold Junction Compensation Kit for Universal Analog Input IC695ALG600

IC695ACC650 Series 90-70 to RX3i Mechanical Frame

IC695ACC651 SERIES 90-70 TO RX3I I/O ADAPTER CARD

IC695ACC652 Series 90-70 to RX3i 5-Slot Conv Rack