EMERSON Motion Control 230V FX Drives 316 340 455(CT)

EMERSON Motion Control 230V FX Drives  316 340 (CT)

• All digital design

• 96-264 1Ø auxiliary logic supply for 1-1000 lb-in, 96-

264 VAC 1Ø bridge power for 0-55 lb-in, 96-264 1Ø or

3Ø bridge power for 55-120 lb-in, 380-460 VAC 3Ø

power for 120-1000 lb-in

• 0-1000 lb-in continuous torque when combined with

DX Series (0-120 lb-in) and BL Series (120-1000 lb-in)

resolver feedback servo motors. IP65 and holding

brake versions available

• FX Series Amplifiers up to 120 lb-in are UL Listed and

Canadian UL Listed. CE Certified versions available

• Easily programmed with EMERSON Motion Control’s

fill-in-the-blank PCXWin or PCX for DOS software

• 8 input and 4 output lines (10 to 30 VDC) sinking or

sourcing are standard on the base FX Drive

• Operating modes: Integral positioner; analog velocity;

analog torque; pulse follower

• Application modules can be installed on the base FX

Drive to add additional I/O (8 inputs, 4 outputs),

memory (Storage for 256 sets of index parameters),

and a wide range of specialty application functionality

• Initiate programs of motion sequences of up to 100

steps total in the base FX Drive and up to 1024 steps

with the addition of an Application Module

• 93 predefined I/O functions for assignment to I/O

lines on the base FX Drive or Application Module

• Non-volatile memory allows storage of up to 32 sets of

index parameters

• Linear or modified sine motion profiles

• Scalable in user-defined units including inches, feet,

mm, etc.

• RS-232 communications interface with baud rates up

to 19.2 Kbaud for daisy chaining up to 31 FX Drives

on a single communication link

• Auxiliary logic supply provision for maintaining

critical drive information (i.e. position) through

bridge power loss

• LED display for operating and diagnostic status

• Two year extended warranty on FX Positioning Servo

Amplifiers

FX brushless positioning servo drives are designed to

provide trouble-free solutions for a wide variety of

industrial automation applications. Each FX Positioning

Servo Drive System integrates the position control, I/O,

feedback, servo amplifier and power supply in one housing.

The drive design allows the unit to operate on a wide range

of voltage sources without needing expensive isolation

transformers.

Models in the FX Drive Series provide up to 1000 lb-in of

continuous torque. FX Amplifiers providing 8 to 120 lb-in

continuous torque are UL Listed, Canadian UL Listed and

CE Certified. These amplifiers are also designed to meet

IEC801 specifications for noise immunity.

FX Amplifiers are matched with EMERSON Motion

Control’s DX and BL Series of Brushless Servo Motors.

These motors utilize advanced mechanical designs and the

latest in magnetic material technology to yield

exceptionally high torque to inertia ratios. These motors

are virtually maintenance free and can be ordered in

splashproof IP65 versions. Thermal sensors provide

additional protection for the motors.

FX Drives are programmed using EMERSON Motion

Control’s PCX Software for DOS or PCXWin for Windows™

software which is included with the purchase of an FX

Drive. This software leads the user through the application

with a simple menu-driven question and answer format.

No knowledge of high-level programming languages is

required.

Dynamic Gain Compensation (DGC), a unique feature of

the FX Servo Drive, eliminates the need for potentiometers

and manual calibration. DGC provides stable operation

over the full torque and velocity range with load-to-motor

inertia mismatches as high as 10:1 out of the box without

any adjustments.

Optically Isolated I/O lines are programmable with status

indicators, choice of current sourcing or sinking for each

line, choice of normally on or off state for most Input lines,

and voltage ranges from 10 to 30 VDC.

FX 280 316 340 455

FX 490 4120 6120

DXE-208 DXM-208

PCM-11 -22Q