EcoStruxureTM Triconex® - Tricon CX

Tricon CX is a flexible SIL3 platform designed for

the protection and mitigation of risks in high-hazard

industries where safe and continuous operation are

imperative. Tricon CX is capable of handling input/

output (I/O) counts of all sizes, from as little as

16 I/O channels in a single system to in excess

of 750,000 I/O channels when deployed across 254

nodes. Systems can be centralized in one location,

as well as distributed across multiple assets. All

modules are fault tolerant and continue to operate

even under fault conditions.

The simple mechanical design of Tricon CX makes

it quick and easy to design, install, operate and

maintain. Only three components are required to

configure a Tricon CX system — the chassis, the

modules, and the connectors.

Modules and connectors are separate, so modules

can be replaced online without disturbing the I/O

modules or wiring.

Chassis are designed for panel mounting or 19”

mounting. No swing frames are required. Front

access only is required — there is no need for rear

access to any of the Tricon CX racks, modules,

or connectors.

I/O modules and connector boards are keyed to

prevent incorrect insertion.

Termination panels are supported and can be used

with Tricon CX for maximum interoperability.

The integrated 24 Vdc power management and

fusing simplifies power distribution, requiring less

wiring, less engineering, less testing, and lower

overall cost.

Chassis

8120X Main chassis

8131X I/O chassis

Processors

3009X Main processor, 256 Mb

Communications

4355X Triconex Communication Module

4610X Unified Communication Module

4701X I/O bus interface module, RS-485 Serial-Serial

I/O modules

3506X Supervised digital input module 32 channels, 24 VDC Supervised, TMR

3626X Supervised digital output module 32 channels, 24 VDC, Supervised, commoned, TMR

3722X Analog input module 32 channels, 0 – 5 VDC, Fast, No-HART, TMR

3723X Analog input module 32 channels, 0 – 5 VDC, HART, TMR

3809X Analog output module 16 channels, 0 – 23 mA, HART, TMR

3902X Universal safety

I/O module 16 channels, TMR

Analog inputs + HART

Supervised digital inputs

Analog outputs + HART

Supervised digital outputs

3506X DI, Supervised 9563X-910 9563X-910

9566X-810 9566X-810

3626X DO 9662X-610 9671X-610, 24 VDC

9671X-810

3722X Al 9760X-210, 2-Wire 4-20 mA, 0–5 VDC

9761X-210

9765X-210, 3-Wire, 4-20 mA, 0–5 VDC

9771X-210

3723X Al + HART 9760X-210, 2-Wire 4-20 mA, 0–5 VDC 9789X-610, 4-20 mA

9761-210 9791X-610

9765X-210, 3-Wire 4-20 mA, 0–5 VDC

9771X-210

3809X AO + HART 9890X-610 n/a

3902X Universal I/O with HART 9960X-610 n/a

Safety specifications are generally applicable to control system handling. Instructions and warnings related to a specific subject or operation of the product.
The following norms must be strictly observed:
 must strictly comply with the technical specifications and typical applications of the product system
 Personnel training: Only trained personnel shall install, operate, maintain or repair the product system. must
Provide guidance and explanation of the situation in danger areas to these personnel.
 Unauthorized changes: Changes or structural changes to the product system may not be made.
 Maintenance responsibility: Must ensure that the product system is used only under appropriate conditions and in full fitness for use.
 Working environment: The user must meet the specified environmental conditions:
Safety regulation
The following safety provisions of EN 50110-1 shall be fully complied with when handling product systems (maintenance) :
1 Disconnect completely.
2 Secure to prevent reconnection.
3 Verify that the installation is complete.
4 Ground and short-circuit the device.

Warning: Only qualified maintenance personnel can remove and insert the module. In order to ensure the personal safety of the operator, before each pulling out or inserting, you must
Disconnect the power supply and ensure that there is no voltage on all terminals at the back, and the product is effectively grounded with the ground screw at the back.