ABB Advant Fieldbus 100 AF100 Control system

ABB CAL16-11A

ABB CB801

ABB CDP312R

ABB CI546

ABB CI547

ABB CI610

ABB CI626

ABB CI626V1

ABB CI627A

ABB CI810B 3BSE020520R1

ABB CI840A

ABB CI853K01

ABB CI854AK01

ABB CI855-1

ABB CI857K01

ABB CI858-1

ABB CI858K01

ABB CI858K01 3BSE018135R1

ABB CI861

ABB CI867K01

ABB CI868K01-eA

ABB CI871

ABB CM10/200

ABB CM572

ABB CP435-T-ETH

ABB CP-A RU

ABB CPU0002

ABB CR-M4LS

ABB CS513

ABB CSA463AE

AC An abbreviation of Advant Controller (used in figures and tables). AF 100 An abbreviation of Advant Fieldbus 100 (used in figures and tables). Advant Controller Advant Controller refers to Advant Controller 70, Advant Controller 110/160 and Advant Controller 400 Series (Advant Controller 410, Advant Controller 450, and Advant Controller 460). 800xA for AC 100 800xA for AC 100 is a connectivity package integrating Advant Controller 100 Series controllers via Advant Fieldbus 100 to the 800xA System. AC 100 OPC Server AC 100 OPC Server provides OPC client applications access to process objects in Advant Controller 100 Series. AF 100 Station AF 100 Station is the name of the “stations” on Advant Fieldbus 100. An AF 100 Station is each item connected to the Advant Fieldbus 100, for example, Advant Controller 70, Advant Controller 110/160, Advant Controller 400 Series, S800 I/O Station, or AC 100 OPC Server.

The TC516 modem has two connections, one for each redundant CI522 and a connection to one twisted pair bus cable. TC516 can be used for two redundant CI522s as well as for one single CI520V1/CI522/CI526V1

Communication Interface Redundancy in Advant Controller 160 For configurations with one Advant Fieldbus 100, the communication interface CI630/CI631 must be placed at position 2 (non redundant interface) or in position 1 and 2 (redundant interface) in the Basic Station. A second and third Advant Fieldbus 100 can be used with AC 160. These can use single or redundant communication interfaces. The communication interfaces can be placed at position 9 and 10, or 11 and 12, and so on

Communication Interface Redundancy in AC 800M The communication interface redundancy in AC 800M is achieved by using two CI869 modules that are connected to the same AC 800M controller. One of the CI869 modules is configured as primary, while the other is configured as backup.

Failover time for CI869 and Double DSP timeout The failover time is the time that the backup CI869 takes to function as primary without error, if the primary CI869 does not work properly. The other stations on the AF 100 bus do not influence the failover of the CI869 modules. The backup CI869 is supervising that the primary CI869 is sending its CDPs with the expected cycle time. If the backup CI869 detects that the Primary CI869 does not send its CDPs as it should, it triggers the AC 800M controller to perform a failover of CI869. The ‘Double DSP timeout’ parameter must be enabled for an AF 100 station that is receiving DSP data from another AF 100 station that uses redundant communication interfaces. For details, refer to the Online Help of Control Builder. Cable Redundancy and Partner Supervision In a redundant configuration, the primary and the backup CI869 modules supervise that the communication happens between them. The backup CI869 supervises that the primary CI869 sends its CDPs as it should. For this, it is required that both the cables that are connected to the backup CI869 have bus traffic. If any of the cables connected to the backup CI869 are without bus traffic for 10 ms or more, the Partner Supervision is disabled, and: • If the parameter "Cable" on the CI869 hardware editor is set to Redundant, the Partner Supervision not active unit status bit is set on the backup CI869 hardware unit. • If the parameter “Cable” is not set to Redundant, the status bit is not set. However, a warning stating that the Partner Supervision requires redundant lines is displayed during the download of this redundant CI869 configuration to the controller.

Advant Controller 410 CI522A AC 410 *1.4 or higher Advant Controller 450 CI522A AC 450 *2.2 or higher Advant OPC Server for AF 100 CI527 OPC Server 2.0 or higher Advant Controller 70 PM810 AC 70 *1.2 or higher S800 I/O Station CI810A CI810 *1.4 or higher S800 I/O Station  (Redundant Field Communication interfaces) CI820 CI820 *2.1 or highe